Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Almost everyone has got their private thinking involving Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is also a reasonably hard job. If the old tub is easily available, the task can move speedily; if you have to open a wall to get rid of the old bathtub as well as position the brand-new bathtub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. See to it you have actually certified on your own for the job as well as are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you may require a professional plumber to make tube links.
This short article will help you mount a new bath tub in your washroom if you have currently purchased a new bathtub and also don't require to change the arrangement of your previous water supply pipes.
Your tools and material checklist ought to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in area between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using both wooden boards under its feet, put the tub in the called for placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the bathtub up until the level reviews level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Turn on the water system as well as inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the tub as well as also examine the overflow outlet and also the normal outlet for leakages.
Lastly, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has actually been utilized at least once as this will resolve it into its last position.
Planning for the Installation
To start with, the sustaining framework provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, leading to complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in use. The sealer can fracture relatively very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that excerpt was a good thing. If you enjoyed our blog posting please don't forget to pass it around. Thank you for your time. Come back soon.
Expert hands available. Report this page